Участник:VitaliyFilippov/Bugs — различия между версиями
Материал из YourcmcWiki
м |
м |
||
| Строка 16: | Строка 16: | ||
* [https://github.com/openscad/openscad/issues/799 OpenSCAD #799 — Auto-indenting in openscad editor] | * [https://github.com/openscad/openscad/issues/799 OpenSCAD #799 — Auto-indenting in openscad editor] | ||
* [https://github.com/openscad/openscad/issues/815 OpenSCAD #815 — Native bend modifier — is it possible to implement in OpenSCAD?] | * [https://github.com/openscad/openscad/issues/815 OpenSCAD #815 — Native bend modifier — is it possible to implement in OpenSCAD?] | ||
| + | * [https://github.com/openscad/openscad/pull/388 OpenSCAD #388 — SVG Importer] | ||
* [https://github.com/alexrj/Slic3r/issues/2049 Slic3r #2049 — Raft/support is generated too low under object in 1.1.2] | * [https://github.com/alexrj/Slic3r/issues/2049 Slic3r #2049 — Raft/support is generated too low under object in 1.1.2] | ||
* [https://github.com/alexrj/Slic3r/issues/1852 Slic3r #1852 — Infills on bridge attempts falling short a perimiter] | * [https://github.com/alexrj/Slic3r/issues/1852 Slic3r #1852 — Infills on bridge attempts falling short a perimiter] | ||
Версия 09:52, 18 июня 2014
Недавние баги, которые я ставил и/или комментил и/или баги, которые меня интересуют. В разных багтрекерах, в основном на гитхабе, который сильно страдает от отсутствия странички «My Bugs» из всех репозиториев… Видимо, предполагалось, что эту функцию должен выполнять Issues Dashboard, но он, похоже, не работает. Правда, есть вариант поискать по author: vitalif. А вот багтрекер KDE — это Bugzilla, и там есть My Bugs.
- Grive #199 — Build fails on 32-bit Debian Wheezy (то же, что Grive #193)
- Grive #201 — Allow to sync just one directory in the root
- Otter #52 — LRU tab switching via Ctrl-Tab
- KMail #327325 — Open message composer in a tab
- QupZilla #1128 — LRU tab switching order (перемещено в QupZilla #1347 — Tabbar improvements in TODO)
- msysgit #163 — SVN is built without SASL support in msysgit — authenticated svn:// does not work
- GwenView #331504 — Enter in crop mode exits it instead of applying changes
- KMenuEdit #57314 — wish: searching for programs and/or Descriptions
- KMix #331582 — Logarithmic volume with ALSA backend! Volume not equal to alsamixer. Broken in 4.10.
- PHP #66095 — Bundled libmagic has public symbols and conflicts with system libmagic
- Samba #6750 — After 'machine password timeout' /etc/krb5.keytab is not updated
- OpenSCAD #391 — Multi-threaded Geometry rendering
- OpenSCAD #114 — Generalized extrusion along a path
- OpenSCAD #414 — customizable face triangulation during stl output
- OpenSCAD #799 — Auto-indenting in openscad editor
- OpenSCAD #815 — Native bend modifier — is it possible to implement in OpenSCAD?
- OpenSCAD #388 — SVG Importer
- Slic3r #2049 — Raft/support is generated too low under object in 1.1.2
- Slic3r #1852 — Infills on bridge attempts falling short a perimiter
- Slic3r #2054 — Bridges printed on multiple thin walls partially hang in the air
- Slic3r #2093 — Strange extra perimeter generated at top interface layer
- Slic3r #2099 — Slic3r crashes when opening Object Settings dialog 2nd time
- GPX #7 — Incorrect progress reported (Sailfish)
- Mesa #80004 — Serious Sam 3 BFE — incorrect weapon rendering
- Kernel #76761 — radeon DPM breaks suspend to disk and resume from RAM in 3.14
